Excalibur Cutting blowpipe NM500 extended - 2000mm OAL.

Due to the length standard shipping rates do not apply to these torches - Quote is required.

These torches are suitable for use with any fuel gas type, acetylene, propane and propylene et cetera along with the appropriate nozzle type,
Noz-Alls provide the widest range of cutting and process nozzles to suit these heavy duty NM cutting blowpipes - also known as a Gas Axe or even a lamp in some industries.
The extended length makes the blowpipe suitable for use with the super heating adaptor and the complete range of Super Heating nozzles from #1H through to the #5H. Due to the NM500 flow rate a much larger heat output is possible when compared to using the #5H Super Heating nozzle on a "Type 5 shank". The extended length helps to ensure you are away from the heat however the weight of the nozzle can be more difficult to control if the torch is not supported.

The NM500 - 2000mm cutting torch could be used for cutting applications with mild steel from 1mm to 500mm thickness and the correct nozzle to suit, however the extended length would make this awkward, therefore these torches are generally used for specific applications where the length is important rather than general use.

Generally Noz-Alls Excalibur blowpipes will cost more than a similar type of torch from a competitor - WHY? Well simply because the Excalibur torch from Noz-Alls is a much better quality torch plus is heavier duty and built to last longer than those supplied by other companies.

While many nozzle mix cutting torches may on the surface look to be similar, our Excalibur cutting torch is much better quality than most.
Every Excalibur blowpipe has:-
A) Solid stainless steel gas control valve spindles which makes for ease of adjustment and extended life. The stainless steel threads run more freely in the brass body when compared to the cheaper brass spindles plus being made from solid stainless steel makes the accuracy better allowing improved control over flow setting.
B) Our 90 degree cutting torch has a robust heavy duty angle head which is larger and thicker than most which mean it can withstand more arduous conditions for longer.
C) The cutting lever may look similar to other torches but Excalibur is made from thicker stainless steel, with large cutting oxygen lever lock button which enables an artisans wearing gauntlets to easily lock the cutting lever on.
D) Unseen by the artisan is the cutting valve which has the original design incorporating the 2 "O" ring seal compared to a single "O" ring seal in the cheaper torches.
E) The cutting valve has a traditional proportional flow control valve rather than the "on - off" valve fitted in low cost torches, the flow control valve we use makes the torch easier to use and work with allowing the artisan ultimate control. The valve design is the original and built to function for the life of the torch.
F) The inlet connections are able to be replaced should they become damaged which extends the life of the torch. Standard threads are G3/8 left and right.
G) The torch handle is made from thick section brass tube so it will not corrode or deteriorate and is much stronger than aluminium. Which makes the torch handle less prone to accidental damage.
H) The lateral strength of the torch comes from the fact the the tubes are 10mm diameter with a thick wall section (many cheap torches use 9mm diameter tube with a thin wall section).

Why buy the torch twice when the Excalibur NM 500 torch will operate more easily, function better allowing the artisan to work more effectively and quickly - saving money and of course the design means the torch will last you for longer than a competitors.

The Excalibur NM 500 - 2000mm cutting torch is available with two head types: 90 degree and 180 degree.

As a special purpose heavy duty cutting torch the long length - 2000mm overall - allows the cutting of thicker section material, to achieve the higher flow rate the cutting valve as standard is the high flow type. However if you will not be cutting thick sections then you can specify the fitting of the proportional flow valve.

Excalibur NM500 72" (2000mm) long

Please allow 4 days for testing purposes.
Normal shipping rates do not apply to extended length cutting torches - due to the length.  A quote will be provided when required.
At Noz-Alls we test each oxy/fuel torch before we ship it out to make sure they are up to our high standards.

Excalibur NM 2000mm nozzle mix cutitng torch generally used with a 90 degree head and support.
Applications may include working on a skid to enable cutting whilst moving such as when cutting hot steel.

Longer cutting torches may be made to order, please enquire.