ANM-6 Cutting Nozzle - All Sizes Available
Premium quality specially designed and manufactured for the RSA market and African markets this ANM has the smaller tip face generally used in these South African market areas.
Price 35.00 Rand each + Delivery
Low cost courier delivery from the UK for a mix of different nozzle styles and sizes works out to be very ecconomic - call Now 0044 1242 681052 We offer the full range of South African nozzle styles we have supplied RSA for more than 20 years.
Our nozzles are better than most in the market and have been designed to perform well they exhibit good backfire resistance. Each of our nozzles will be capable of turning down to 50% flow and remain stable in use. Size 2,8 & 3,2mm will turn down by 25% due to the size.
Please note that our ANM-6 cutting nozzles have different pre-heat flows for each nozzle size to ensure the heat output is correct for the thickness being cut. The size 2,4mm is the largest that may be used on s single large industrial Afrox Acetylene cylinder due to the flow rate of acetylene.
Noz-Alls
Noz-Alls Afrox type ANM-6 (Acetylene Nozzle Mix - 6 pre-heat cones) cutting nozzles have the small tip diameter for maximum visability. These ANM cutting nozzles are easy to work with because they exhibit good resistance to backfire combined with focused pre-heat flame cones which are essential qualities required
for initiating and maintaining the cutting process thereby giving you the confidence to work quickly and efficiently without experiencing operating problems.
Noz-Alls
Produced to Noz-Alls own drawings we know that our Afrox style ANM nozzles work safely and effectively giving you a safer and longer lasting nozzle compared to cheap versions that you can find in the market. Ensure that you complete your kit with something that works. Our Afrox style ANM-6 cutting nozzles have the original larger barrel diameter which is 15.4 - 15.6 mm plus our nozzle length is the original 75mm which helps provides the optimum performance.
For your safety and that of those around you it is important that you do not use ANM-6 cutting nozzles on small / medium size acetylene cylinders (PortaPak / "J" size) this is because the ANM-6 nozzle even the smallest size 0,8mm will draw off too much acetylene therefore it is important to use only the AFN / ASFN cutting nozzle range with small and medium size DA cylinders.
From regulators, flash back arrestors, hoses, quick connectors and torches, we have everything you could possibly need to go with your nozzles. Please feel free to browse in the related products section as well as the rest of our website.
The ANM range cuts from 3mm to 300mm. Please see our size information table below.
Nozzle
Size
(mm)
|
Nozzle
Size
(mm)
|
Cutting
Thickness
(mm)
|
Acetylene
Pressure
(bar)
|
Oxygen
Pressure
(bar)
|
0,8 |
0.8 |
3-6 |
0.3 |
1.5 |
1,2 |
1.2 |
5-12 |
0.35 |
1.8-2.2 |
1,6 |
1.6 |
10-75 |
0.4 |
2.6-3.5 |
2,0 |
2.0 |
70-100 |
0.4 |
3.1 |
2,4 |
2.4 |
90-150 |
0.4 |
2.8-3.2 |
2,8 |
2.8 |
140-200 |
0.45 |
3.1-3.7 |
3,2 |
3.2 |
190-300 |
0.45 |
4.5-6.2 |
ANME's also cut the same range but offer a longer tip with increased backfire resistance. We also offer an ANME in a long taper version to help with cutting vision.
To cut more than 300mm please see our 'Heavy Duty ANME' in the related products section.
Typical part numbers for these nozzles would be:-
W005 014, W005 015, W005 016, W005 017, W005 018, W005 019 & W005 020
Why Its Important to Pay the Right Price For Your Nozzles
When you pick up an ANM-6 in your hand what do you see, is it just a lump of copper with 20 holes in it with 10 external diameters and 3 tapers?
Well typically that is what you see when you examine an ANM no matter whose ANM or ANME cutting nozzle you have purchased.
Very few people have sufficient experience to understand nozzle design and that although the external dimensions are important for most of those dimensions it is the internal sizes that dictate nozzle performance and those you cannot see.
Have you ever considered what makes the ANM-6 cutting nozzle function and operate correctly? Well it all comes down to the internal design and manufacturing process, that is what determines just how the nozzle performs it is the arrangement of the internal holes and their sizes that makes all the difference to each nozzle.
Inside each ANM-6 there are 33 different diameter holes 6 individual mixing systems each of 5 different diameters and those hole diameters each interacting with the other to help provide the correct flame characteristics.
The design is not particularly difficult to achieve when made correctly however it is important for the design to be correct.
How do companies make cheap ANM nozzles, well to cut the cost of the nozzle – they simply take out some of the internal operations and hole diameters.
Due to the fact the changes are made internally you cannot see the cheapening of the nozzle.
To the untrained eye removing operations which may seem to be superfluous result in an inferior nozzle with poor performance when it counts.
Less processing means less operations and less cost in manufacturing with quicker processing resulting in a cheap nozzle.
Externally the result looks the same and you would never know as the inside goes unnoticed until the nozzle doesn’t work correctly.